Belkin n150 validating identity

Posted by / 25-Feb-2016 01:26

Step 6 Select the Connection tab and check the Connect when this network is in range box.Step 7 Select the Association tab and uncheck the “The key is provided for me automatically” box, then select Network Authentication & Data encryption and type in the Network key according to the wireless settings on your [email protected] /boot $ iwlist scan lo Interface doesn't support scanning.wlan0 Scan completed : Cell 01 - Address: 00:1F:: C Channel:11 Frequency:2.462 GHz (Channel 11) Quality=70/70 Signal level=-24 d Bm Encryption key:on ESSID:"\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00" Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s 12 Mb/s; 24 Mb/s; 36 Mb/s Bit Rates:9 Mb/s; 18 Mb/s; 48 Mb/s; 54 Mb/s Mode: Master Extra:tsf=00000000c3bd6181 Extra: Last beacon: 3700ms ago IE: Unknown: 000E0000000000000000000000000000 IE: Unknown: 010882848B960C183048 IE: Unknown: 03010B IE: Unknown: 050400010000 IE: Unknown: 2A0100 IE: Unknown: 32041224606C IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : CCMP Pairwise Ciphers (1) : CCMP Authentication Suites (1) : PSK Preauthentication Supported eth0 Interface doesn't support scanning.If the box was checked, then that was why you were getting the “unable to find a certificate to log you on to the network” message because Windows is looking for one, but your wireless router is not setup for certificate security. Once I unchecked that box and tried to reconnect to the wireless network, everything worked fine!

Select Properties once you locate the wireless network causing the error.When you try to log onto a wireless network, you may see this error message: “Windows was unable to find a certificate to log you onto the network xxxx”. Step 2 Double-click Network Connections in the new window.This error is typically related to wireless network authentication and often appears because your Windows device is mistakenly searching for an 802.1x connection. Step 3 Right-click wireless network connection, then select [email protected] /boot $ [email protected] /boot $ ifconfig eth0 Link encap: Ethernet HWaddr b:eb:6c: inet addr:10.0.0.3 Bcast:10.0.0.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:10096 errors:0 dropped:0 overruns:0 frame:0 TX packets:7485 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:9304609 (8.8 Mi B) TX bytes:829233 (809.7 Ki B) lo Link encap: Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) wlan0 Link encap: Ethernet HWaddr c4:3d:c7:bc:34:db UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) [email protected] /boot $ [email protected] ~ $ dmesg [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 3.2.27 ([email protected]) (gcc version 4.7.2 20120731 (prerelease) (crosstool-NG linaro-1.13.1 bzr2458 - Linaro GCC 2012.08) ) #250 PREEMPT Thu Oct 18 BST 2012 [ 0.000000] CPU: ARMv6-compatible processor [410fb767] revision 7 (ARMv7), cr=00c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT nonaliasing instruction cache [ 0.000000] Machine: BCM2708 [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] On node 0 totalpages: 114688 [ 0.000000] free_area_init_node: node 0, pgdat c050db28, node_mem_map c05b6000 [ 0.000000] Normal zone: 896 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 113792 pages, LIFO batch:31 [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on.To fix, you go into the properties page of your wireless connection, go to "Wireless Networks" tab and then to Properties of the chosen wireless network you are trying to connect to.

belkin n150 validating identity-61belkin n150 validating identity-8belkin n150 validating identity-62

When I tap on connect, i can see 'Failed to initiate AP Scan' message in the progress.